Washing machines of the Samsung brand are widely represented on the domestic market. Their popularity is associated with high reliability and the use of innovative technologies.
But even such equipment is not immune from possible breakdowns. One option is the need to replace the belt. This type of work is a moderately complex repair, and you can even do it yourself.
We will tell you in the article how to change the belt on a Samsung washing machine (remove the old one, put on a new one).
Signs that a part requires replacement
The need to replace a belt is not a common problem. Worn parts can become noticeable during prolonged or improper use of the washing machine.
The average service life of a washing machine belt is 6 years. The need for replacement during longer use is a normal situation.
with regular violation of the rules, for example, overloading laundry, can accelerate the wear of a part
In some cases, a problem with the drive belt may be indicated by a complete stop of the washing machine and the display of code E4, , UB. On machines not equipped with a display, all mode lights blink and the second temperature indicator from the top lights up.
A problem with the drive belt does not always cause an error code to appear.
It is necessary to pay attention to the following failure situations:
- when water is filled into the drum and the motor is running, the drum does not rotate;
- the engine runs intermittently;
- after the start of the work cycle, despite the engine running, a freeze occurs;
- free rotation of the drum when the engine is not running.
- Uncharacteristic noise when washing.
If the part itself has a rough surface, pellets have formed on the surface and on the elements that are in contact with the belt, or delamination, then replacement is definitely needed. But this can only be determined through direct access.
If problems with the drive belt occur frequently, professional diagnostics of the machine by a specialist is necessary.
Fault diagnosis
Replacing the belt of a Samsung washing machine will require removing the back panel, disconnecting the device from electricity and the water supply network, so the first thing you need to do is make sure that the drive belt is the cause of the non-operation of the household appliance. This malfunction may have the following symptoms:
- The motor runs, but the drum does not rotate.
- The drum rotates jerkily, and the smell of burnt rubber is felt in the air.
- Extraneous sounds are heard when the drum rotates.
This important part of the washing machine does not always fail so much that the household appliance stops working. In the early stages of wear of this part, problems can only occur when the washing machine is fully loaded. If in such a situation the drum begins to jam, then you should not wait for the situation when the engine jams or a loose belt breaks the internal wiring wires. If you suspect such a problem, you should immediately begin troubleshooting the problem.
[custom_ads_shortcode1]
Preparation for the process
Replacing the drive belt is carried out by partially disassembling the structure of the washing machine. Therefore, you need to prepare:
If there is water in the washing machine, it must be drained and the laundry must be removed from the drum.- Disconnect the device from all communications. You should not only turn off the machine with the button, but also remove the plug from the socket.
- Move the machine so that you can access the back wall.
- Prepare tools - a set of screwdrivers.
If the part has flown off for the first time and has no visual damage, it can simply be returned to its place without replacement.
Installing a belt on a Samsung washing machine
Before repairing, you should purchase a new pass. The Samsung model range (Samsung S1021, S803J, S821 and others) is equipped with a yellow Italian Megadyne 1270j3 strap. How can I replace a part if there is no similar one? The black pass 1270j4 is suitable - it has less stretch, which will complicate the installation process a little, but the system will last longer, thanks to the additional “trickle”.
Before the procedure, disconnect the SM from the power supply, communications, and move it away from the wall. To work you will need a screwdriver and a strong cord. Having an assistant will save time and effort.
[custom_ads_shortcode1]
Two belt access options
The belt can be accessed from the back wall of the washing machine, if it is removable, or through the top.
Since many Samsung models do not have access to the elements of the washing machine from the rear wall, the job of replacing the belt becomes much more complicated.
Procedure for machines with a removable back panel:
- Unscrew all the screws that hold this cover in place.
- Remove the cover. This allows you to get a good overview and convenience when replacing parts.
Otherwise, you will have to work through the top of the machine. For this, the steps will be as follows:
- unscrew the screws that hold the top cover;
- lightly push the cover towards the back wall so that it is removed from the grooves;
- remove the cover.
The immediate procedure for replacing the belt does not depend on the method of access to the part.
Causes of failure of the washing machine drive belt
There may be several reasons for the failure of the drive of washing machines Samsung, Zanussi, Indesit and others:
- Operational wear. The part fails naturally. The belt fabric may wear out during use. A rupture appears at the point of deformation and disables the device. If you have been using a washing machine for several years and have never repaired this part, you should think about it and inspect the main components.
- Bearing wear. In this case, parts shift and the belt warps. It is often impossible to know in advance about bearing wear. If they are replaced, the malfunction will not recur.
- Deformation of the motor or pulley mounts.
- Incorrect installation of a part during repair.
- Damage to crosspieces.
How to install a new one?
In order to replace the belt, you must first dismantle the old part and then install the new part. First you need to determine whether it is on the drum pulley. If it's not there, it's probably torn or fallen off completely and fallen to the bottom.
How to tension a new belt? Procedure for machines with a non-removable back side:
The car must be tilted towards itself so that the tank sag towards the hatch, and the gap between it and the rear wall becomes larger.- The old part must be pryed off with a screwdriver and removed from the pulley by sliding it.
- While holding the belt, you need to rotate the pulley. This will help release the rubber or polyurethane part.
- Use a flashlight to illuminate the area where you are working to see if any parts of the belt remain un-removed if it has become frayed due to wear. If they are detected, it is necessary to remove all fragments so that they do not interfere with normal operation in the future.
- Place the new part onto the engine pulley. If you have to work through the top of the machine, you can use the help of a second person to grab the belt through the bottom. Or help yourself hook it by lowering it on a wire loop.
- After the part is draped over the engine, you need to pull it onto the pulley grooves. This must be done by holding the belt itself taut and turning the pulley clockwise.
- To make sure that the belt is “sat” in place, rotate the pulley.
- Reassemble the washing machine in reverse order.
- Run a test wash.
Replacing a belt in a Samsung machine
To replace the drive belt, proceed as follows:
- Remove the back panel by unscrewing the fasteners.
- For models that do not have a removable back panel, you must remove the front panel. In this case, work is carried out from above.
To remove the front panel:
- Unscrew the lid.
- Take out the powder dispenser (it has a small button inside for easy removal).
- Remove the control panel and place it on top out of the way.
- Unscrew the bottom panel.
- Unscrew all the screws that secure the front cover and pull it towards you.
- Arm yourself with a slotted screwdriver - using it carefully, lightly hook the edge of the belt.
- Remove the belt from the grooves on the pulley by sliding it to the side.
- Rotate the pulley while holding the strap with your hand. After this, the belt should easily come off the pulley and you can safely remove it from the housing.
Important! If there is a “beard” and it is wrapped around the engine, be sure to untangle everything and remove it.
Important! Buy a part with 5 streams (Megaden production is suitable). Buyers respond positively to it, praising the quality and especially the silicone inserts that extend service life.
Don't know how to tighten the belt in a Samsung washing machine? All the hardest parts are already behind you - all you have left are the final chords. Just a few steps separate you from using an updated machine:
- Place the new part on the pulley so that the grooves line up as specified by the manufacturer.
- If you work from above the CM, then help yourself with a strong thread or a piece of used belt. Tie the belt to an improvised “fishing rod” and lower it into the body. Hold it with one hand and put it on the engine with the other.
- Now stretch and place the part on the side grooves on the pulley.
- Continuing to create tension, rotate the pulley to the right and everything will fall into place.
If you have a Samsung S1021, S803J or S803J model, now you know how to remove and install the drive belt. For other SM models, the replacement process is similar.
We hope the installation goes smoothly and successfully. Good luck with your renovation!
You can handle some washing machine breakdowns yourself. Even if you have no experience in repairing complex household appliances, replacing the belt can be done within a short time. This operation does not require expensive equipment, and all you need is a screwdriver and an adjustable wrench. How to change the belt on a Samsung washing machine will be discussed in detail in this article.
How to choose, how much to pay and where to buy?
The best option is to replace the belt with an original one that fully matches all the parameters of the washing machine. You should choose a part taking into account the characteristics of your washing machine, so you can simply remove the worn one and buy exactly the same one .
Poly V-belts, which are not smooth on the inside and have a textured surface of several wedges, have proven themselves to work well.
An important parameter for poly-V belts is the distance between the wedges. For Samsung, the “J” type works well, which means a distance of 2.34 mm. This parameter is indicated on the part itself.
Near the letter on the surface itself the number of wedges is indicated . There can be up to 5 of them. J3 is suitable for narrow Samsung devices, and J5 for wide ones.
The length of the belt is also indicated directly on it. This is an important parameter that cannot be ignored, because otherwise the part will not fit the machine.
For Samsung cars - 1270. Thus, the marking 1270 J3 indicates a poly-V-ribbed three-ribbed belt with J-type wedges and a total length of 1270.
Belts are made from rubber and polyurethane. It is even possible to determine the type of material visually: rubber ones are black, polyurethane ones are light . The former have a longer service life.
A good three-ribbed belt 127 cm Megadyne (made in Italy) costs from 420 rubles. One of the cheaper options is also suitable, which can be ordered, for example, on Yandex.Market or bought in a specialized store.
Prices for simpler product options start from 200 rubles. They are inferior in quality and less durable, but gain in price. A wider belt has better grip and is less likely to slip.
Calling a specialist: the price of the issue
If it is impossible to replace the drive belt yourself, you must call a technician from a company that repairs household appliances. You can find a company on the Internet. A professional technician will do all the work, conduct diagnostics and give recommendations .
On average, the cost of replacing a belt will be up to 1,000 rubles. The new part itself is paid separately.
When calling a specialist to replace a belt, you must indicate the make of the machine, as well as whether a new part is available or the technician needs to bring it with him. If the technician additionally has to fix other faults, the amount will be higher.
For machines that are still under warranty, you should call a specialist only from the service center . All information about such companies must be in the documents for the washing machine.
Contacting specialists through private advertisements can be dangerous, since there is a significant chance of ending up with unscrupulous workers, weak specialists or simply scammers. Contacting a company that has been in the service provision market for a long time will help eliminate the risk.
All the most important and useful information about repairing Samsung washing machines is in this section.
How much does it cost to replace the drive belt on a washing machine?
The price for replacing a washing machine belt is from 900 rubles
, excluding the cost of a new part. It will cost the same amount to put a belt on a washing machine drum pulley if it comes off. Included in the price:
- visit of the master,
- machine disassembly,
- installing the drive belt,
- machine assembly.
You can find out a more accurate cost of work, depending on the brand of your washing machine, from this table.
*
PRICE DOES NOT INCLUDE the cost of a new drive belt.
You can check the cost of a new part with a RemBytTech specialist, specifying the model and brand of your washing machine. [custom_ads_shortcode2]
