Causes and diagnosis
The appearance of F05 on the display does not always indicate a serious breakdown of the device. In some cases, the problem lies in poor care of the machine.
Reasons for the impossibility of draining:
- breakdown of the pressure switch;
- pump failure;
- clogged sewer system;
- clogged drain hose;
- filter contamination.
In rare cases in autumn, the reason for the lack of drainage may be a breakdown of the control module.
Sometimes the appearance of F05 is a system failure, which a reboot will help resolve. Do it as follows:
- Turn off the power by pressing the on/off button.
- Remove the plug from the socket.
- Leave the machine turned off for 20-30 minutes.
- Connect the device to the mains.
- Press the power button on the washing machine body.
- Run a short wash cycle without adding laundry or washing powder.
If the error no longer appears, you can continue to operate the washing machine. Otherwise, you will have to sequentially diagnose the nodes involved in the process.
Sewer blockage
If the sewage system of an apartment or house is clogged, it will be difficult to drain water not only from the washing machine, but also from the sink and bathtub. You can clean the sewer pipes either yourself (for example, with a special plumbing cable) or by calling a plumber.
To make sure that the problem is not in the washing machine, you can follow these steps:
disconnect the washing machine from the power supply;- disconnect the drain hose from the sewer connection, if possible;
- throw the free end of the hose into the sink or bathtub;
- connect the washing machine to the mains;
- select the “drain” mode;
- if water flows from the hose, we can conclude that the problem lies not in the washing machine, but in a clogged sewer;
- clean the sewer system;
- install the free end of the drain hose of the machine in the same place where it was inserted into the pipe.
Otherwise, if error code F05 still appears, you need to proceed with sequential diagnostics of the functionality of the washing machine. It is advisable to start with units that are easier to access and repair, and then move on to complex ones.
The drain filter and hose are clogged
The drain filter in the washing machine is designed to catch small foreign objects that have fallen into the drum. These could be threads, torn buttons, coins, etc.
The filter is located on the front side of the machine below the panel. When cleaning this unit, you should prepare rags and a low container for draining water from the washing machine in advance.
Procedure:
- Open the panel from below, on the front side of the machine.
- To remove the filter, you need to turn it from left to right and pull it towards you.
- Clean the filter manually.
- Return everything to its previous state.
To prevent this situation from occurring, the filter should be cleaned regularly.
The procedure for removing and cleaning the drain hose can be seen in the video:
Breakdown of the pressure switch
If there is no sewer blockage, the drain filter is not clogged, the reason for the malfunction of the Indesit washing machine may be a malfunction of the pressure switch or pump.
Pressostat – water level sensor. If it breaks down, after draining the water, the corresponding information does not enter the control module, and the operation of the machine stops.
Diagnosis of the condition of the unit should be carried out when communications are disconnected, without power, and after draining the water.
Procedure:
remove the top cover;- inspect the part for damage, reliability of contacts, etc.;
- disconnect and inspect the supply tube - any deformation can cause error F05 to appear;
- the removed part should be tested using a multimeter in resistance test mode;
- If there are burnt areas of contacts on the body, it is recommended to replace the sensor.
Inspecting this unit is a more difficult job than cleaning the filter, so if you do not have the skills to work with equipment, entrust the diagnosis and repair to a specialist.
Pump malfunction
A pump that has become unusable is one of the most common reasons leading to F05. The pump is a pump, it is located at the bottom of the Indesit washing machine.
Work order:
- Disconnect the washing machine from communications.
- Drain the water.
- Carefully place the washing machine on its left side.
- Disconnect the pump from the wires and pipes.
- Check the functionality of the impeller - it should turn without effort.
- Make sure there are no external defects on the part.
- Check the condition of the contacts and clean them if necessary.
- Clean the pump. To do this, unscrew the screws that connect the two halves of the part.
- Connect the elements of the pump and return it to its place, connecting the pipes and wires.
- Check the connections are secure.
If the inspection results reveal defects in the pump, it should be replaced. To determine whether there is an interturn short circuit, you must use a multimeter.
It is advisable to combine cleaning the pump with cleaning the supply pipes.
You can see how to deal with the problem in the video:
Electronic control module failure
The control module has a complex organization . Various factors can affect its operation - from condensation on the surface to burnt-out board elements. If the surface of the board is wet, it should be dried, as this defect can cause short circuits.
Failure may be indicated by melting of element bodies, dark spots and other external defects. But it is better to entrust full-fledged comprehensive diagnostics and repair of this unit to professionals.
Causes of malfunction
In the Indesit washing machine, the appearance of error F 05 indicates problems with draining the waste solution. This causes various side effects. If the water sensor breaks down, a signal is not transmitted indicating that the system is completely empty. As a result, the program is unable to proceed to further work. A software failure occurs in the device and code F 05 is displayed on the screen.
However, depending on the features of the indesit washing machine model, the fault message is reported differently. If it is an electromechanical SMA that is not equipped with a display, then the “Spin” and “Soak” indicators flash simultaneously on its control panel. In other washing machines, these may be lights indicating “Extra Rinse” and “Super Wash”.
The reasons for such a breakdown may be the following:
- severe clogging of the drain hose when the used soap solution does not pass into the sewer;
- malfunction in the drain pump;
- acceptance of false information by the water level sensor as reliable.
Call the master
In cases where the decision is made to call a technician, it is necessary to find a company that specializes in repairing household appliances , in particular Indesit washing machines. Such companies can easily be found on the Internet.
The company's website provides the necessary information, contacts and prices. If you need to clarify any details, it is better to do this by phone while communicating with the dispatcher.
The cost of repairing an Indesit washing machine with error code F05 is in a wide range.
The final price is affected by:
- complexity and volume of work;
- company pricing policy;
- the need to replace individual parts or entire units.
Average prices for repair work in the capital (excluding the cost of parts):
- replacement of the drain filter – from 1,300 rubles;
- cleaning the drain filter – from 1,000 rubles;
- replacement of the drain pump – from 1,600 rubles;
- replacement of a pressure switch - from 1,6000 rubles, etc.
Companies that have been in the service provision market for a long time are fighting for their reputation - they have positive reviews from clients and always provide a guarantee for the work performed.
Error codes for Indesit washing machines
Indesit washing machines are equipped with a self-diagnosis system. A failure in normal operation is manifested by a sharp sound signal, blinking indicators, and most importantly, a failure code appears on the display. The machine is capable of recognizing certain malfunctions and incorrect operating modes.
Failure to operate does not always indicate a malfunction. This is often the result of a slight freeze in the electronics. It is enough to turn off the power to the device for 20 minutes and turn it on again - the problem disappears. Such manipulation should always be number one on the list of repairs.
If operation does not resume in normal mode, you need to look at what code number is displayed on the display and carefully read the operating instructions.
All faults can be divided into certain groups.
It is better to entrust the repair of washing machines to professionals!!!
We present to you our unique catalog of private craftsmen and service centers —
Select your city and artist in the filter: by rating, reviews, price!
Engine malfunction - F01, F02
Both problems are characterized by the failure to start working when you press the “Start” button.
Code F01 indicates problems in the engine electrical circuits. Typically, this is a short circuit due to a leak in the motor. In addition, first of all you need to check:
- the value of the rated network voltage;
- integrity of the cord and socket.
If no breakdown is found, you need to inspect the motor itself - the graphite brushes may be worn out or the triac may have burned out.
Steps to troubleshoot error F01 are shown in this video:
Fault code F02 refers to the tachogenerator. It is necessary to check all wiring contact connections in the motor-sensor-board control circuit. The failure may be caused by problems in the control system.
Diagnosis of fault F02 and instructions for eliminating it are discussed in this video:
Error in the functioning of the sensors - F03, F04, F07, F13
The display of code F03 indicates a failure of the temperature sensor or a malfunction of the relay that turns on the heating element. Need to check:
- thermostat contact connectors;
- The tester needs to measure the resistance of the sensor, it should be within 20 kOhm.
Recommendations for diagnosing and eliminating error F03 are shown in this video:
Error F04 - the water level sensor is faulty. It does not enter the system in full. To eliminate it you need to:
- make sure there is water at the inlet;
- inspect the supply hoses and tubes;
- check the operation of the contacts of the water level meter;
- make sure that the water supply valve is movable.
If error F07 occurs, similar actions must be taken; the error may be caused by a malfunction in the pressure switch. Additionally, you need to check if there is a blockage in the filter.
Indication F13 is typical for machines with clothes drying. As a rule, in this case, a simple reboot helps; if not, you need to change the drying thermometer.
Incorrect operation of the drain-fill mode - F05, F10, F11
A series of malfunctions related to the operation of the drain pump. Characteristic manifestations are:
- the system signals when the tank is empty;
- spinning and rinsing do not work;
- there is no pumping of water.
Initially, it is necessary to diagnose the drain filter. A clogged filter usually causes the pump to burn out and has to be replaced.
Other causes of problems include a breakdown of the water supply valve, a break in the wiring in the pump-board section, or a failure of the control board itself.
Diagnosis of error F10 and instructions for eliminating it are discussed in this video:
Malfunction of electronics - F06, F09, F12, F18
The appearance of these values on the display indicates a failure of the control motherboard. You can also try:
- reboot the system by turning off the machine for half an hour;
- carefully check all electrical circuits.
If these measures do not produce results, you need to call a specialized specialist to reflash or reinstall the board.
How computer diagnostics and flashing of the motherboard of a washing machine occurs, see this video:
Failure of the heating element - F08, F14, F15
Code F08 is the most common, it signals that the tubular heater is not working. The reason may be:
- water level sensor malfunction;
- break in the control circuit circuit;
- blockage in the water supply system.
Based on the diagnostic results, it is necessary to either replace the heating element or change one of the sensors.
Diagnostics and troubleshooting for error F08 are discussed in this video:
What to do for prevention?
In order to minimize the likelihood of error F05 occurring, preventive measures should be taken:
- The drain filter must be cleaned periodically to prevent it from becoming clogged.
- It is necessary to maintain the sewerage system in working order.
- You need to try to prevent foreign objects from getting into the tank - check the pockets of things, fasten zippers, etc.
- Water and other liquids should not be allowed to flow into the upper part of the washing machine, as this is where the control module is located.
Recommendations
The following expert advice will help you with your work:
- You must not tilt, much less place, the washing machine on its side until the water has been drained from it.
- Complex repairs should be entrusted to a specialist.
- Parts with serious damage (pressure switch, pump) require replacement.
- When dismantling or installing parts, do not use force, as this can lead to damage to the fasteners, breakage of the part itself and other components.
- After the repair has been completed, the washing machine should first be started in test mode, without loading it with laundry and without adding washing powder.
Read about decoding error codes for Indesit washing machines in this section.
