How to turn off the spin cycle in a washing machine?

The program algorithms of modern washing machines are constructed in such a way that during their execution, each stage may include one or more procedures. When switching between global modes (for example, from washing to rinsing), waste water is drained and spinned. If it is not possible to perform any procedure, the washing machine (depending on the model and type of malfunction) may give an error or stop the process completely. There are a number of critical faults that make the washing machine impossible to operate. One of these problems is the lack of spin. This article discusses possible causes of such a malfunction and ways to eliminate them, both with the involvement of a specialist and independently.

The engine is not working correctly

The lack of spinning has several manifestations, and the type of repair directly depends on how this occurs. In the first option, the program does not stop until the end, but the laundry remains wet. In the second case, having reached the spin cycle, the washing process is interrupted and the machine stops without completing the program.

If the laundry is not wrung out after finishing washing and unlocking the hatch, then most likely the spin mode was turned on, but it did not reach the required 400-1800 revolutions. Then you should pay attention to the performance of the engine and its connection circuits, and the malfunction may lie in the tachogenerator. The washing machine engine is turned on by the control unit and, based on the required washing mode, the module switches on the required speed. If the electronic unit malfunctions, the spin mode may not turn on, and instead of increasing the speed, this stage will take place at a rotation speed similar to washing or rinsing. An electronics specialist must diagnose and repair a malfunction of the control module. Repairing or replacing the unit with a new one is an expensive procedure and is not always advisable. This is especially true for old washing machines, because spare parts for them are either already discontinued or made to order and cost about 70% of the cost of a new device.

Just as in the case of a faulty unit, a malfunction of the engine or tachogenerator appears. Most installations have a motor with brushes and slip rings. They wear out over time and, due to poor contact, cannot spin the engine to the required speed. During repairs, they will need to be replaced and perhaps this will solve the problem. If the symptoms remain after replacing the brush assembly, then most likely there is a malfunction in the motor itself (the winding on the stator or rotor is damaged). This malfunction can be eliminated by replacing the motor with a new one.

A breakdown of the tachogenerator can also lead to unstable engine operation and the absence of an increased number of revolutions per minute during spinning. A tachometer is a device used to transmit information about the speed and direction of rotation from the engine to the central control unit. Based on the readings from this sensor, the electronic controller turns on one or another rotation mode required for each stage of the program. Failure of this device can lead to incorrect behavior of the machine (rapid rotation during washing, starting the motor jerkily, or lack of the required spin speed). The tachogenerator is an expensive spare part and is unique to most models of washing machines. You need to order it by serial number or by sample from trusted, official suppliers.

How to use the spin mode

There are no difficulties in using the function. Even an “inexperienced” user can handle this. The procedure involves the following sequence of actions:

1. We put clothes in the SMA drum. The volume of things will depend on the maximum allowable load of a particular washing machine model. Overloading of linen, as well as its shortage, should be avoided. Because this may cause an error in the software.
2. Close the hatch door.
3. Turn the toggle switch to the “Spin” icon.
4. Using the handle or pressing the button with the corresponding inscription, we set the drum rotation speed (revolutions per minute).
   Let us remind you! The selection may be automatically limited depending on which program was initially selected.
5. We start the program by pressing the “Start/Pause” button.

Most SMAs (Bosch, Samsung, Candy and others) have the ability to change the drum rotation speed not only before starting the program, but also in the middle of the cycle without stopping it.

Doesn't drain and therefore doesn't wring out

If the machine does not spin out the laundry, but stops with water and nothing happens, then the problem is in the drainage system. Often you may not notice whether there was a rinse mode or not, but pay attention to the fact that the washing machine has stopped, the door is locked, and there is water and laundry in the tank. Many users believe that the machine does not have a spin cycle, but in fact, the system for pumping water from the tank is broken. The first thing you can check yourself in such a situation is to open the drain filter and find out if there is any debris or foreign objects in it that interfere with the operation of the drain pump. If everything is clean, then the intervention of a specialist will be required, who will diagnose the device for the functionality of the drain pump and the integrity of the wiring connecting it. If a malfunction is detected in this unit, it will need to be replaced and the drain system cleaned.

There is another important detail in the washing machine that affects pumping, as well as water intake - the pressure switch. This is a level sensor installed in the tank and transmits readings about the water level to the electronic control unit. If there is a malfunction in its operation, the water may not be drained (if, when there is water, the sensor shows that the tank is empty), and the program will not go into spin mode (if, when the tank is empty, it shows that the water has not been drained). If the pressure switch readings are incorrect, you can disassemble it and try to clean it (often, due to debris, malfunctions may occur). If cleaning does not help, then it needs to be replaced. Older models of equipment were equipped with analog sensors, the replacement of which is relatively inexpensive, but there is a problem with their availability. Modern devices have more reliable digital pressure switches; they break down much less frequently, but if this happens, the cost of replacement can cost the user as much as half a washing machine.

Instructions for activating the spin cycle

Running only the spin mode on LG washing machines is very simple. After turning on the washing machine, the user should not immediately turn the programmer knob to select the appropriate program. In fact, you don't need a selector at all. To activate the spin cycle, you must use exclusively the button of the same name located on the control panel. The sequence of actions will be as follows:

• press the network button (which turns on the equipment);
• wait until the indicators on the control panel light up and the machine emits a characteristic sound signal;
• press the “Spin” key several times to set the desired drum rotation speed. At this time, the display will show the approximate time of the process;
• Start the washing machine by pressing the “Start” button. Wait for the equipment to wring out the laundry and remove the water from the tank.

By following the mentioned instructions exactly, you can be sure that the washing machine will not begin to collect water for rinsing, but will immediately begin spinning. Having selected the “Rinse plus Spin” program using the selector, be prepared that the device will first collect liquid, rinse things and only then begin spinning. And this promises an extra 10 minutes of equipment operation and several dozen wasted liters of water.

Some LG washing machine models do not respond to the algorithm described above.

This is not a reason to be upset; you can run “Spin” separately like this:

• turn on the automatic machine, use the selector to select the “Rinse and Spin” mode;
• turn off the equipment by pressing the power key. The intellect will remember the last command given to it;
• turn on the washer again. At this stage, it is important not to touch the programmer knob;
• press the “Spin” key as many times as needed to set the optimal speed;
• start the program by pressing the "Start" key.

A little trick will help the user turn on the spin. If using the described methods it was not possible to start the mode, your “home assistant” probably has problems with the software, or a couple of buttons on the control panel do not work. In this case, you should invite a specialist to carry out diagnostics.

Call a repairman

When diagnosing and repairing problems related to the motor or drain, many users, trying to save money, invite a private self-taught technician. And since the main difficulty lies precisely in identifying the faulty unit, and not in replacing it, most craftsmen begin to replace spare parts one by one, without determining specifically where the breakdown occurred. This kind of savings can lead to even greater costs than calling a specialist from an authorized service center. A professional with special equipment is able to accurately determine which spare part has become unusable and replace it. But the price of such repairs will not be cheap due to the cost of original spare parts and payment for the work of a qualified technician. The only thing that craftsmen rarely inform the client about, in order not to lose income, is that during the diagnostic process some other defects were discovered that will soon make themselves felt. It often happens that there is no point in reviving an old washing machine, but you should think about purchasing a new one.

High-quality Miele washing machines

When choosing a new washing machine, you should pay attention to the products of the premium brand Miele. There is a well-established expression among appliance repair specialists: “Miele machines don’t break.” And this is partly true, based on many years of experience in workshops, where for every hundred units of equipment brought, there will be one, or even none at all, of this brand. Such high reliability is due to the use of the most advanced technologies in the development and production of each part. The Miele range offers a variety of built-in and free-standing designs. There are devices that can be installed in a column with other equipment, as well as those that can be quietly integrated into furniture and add uniqueness and functionality to the workspace.

Recommendations for users

Indesit brand washing equipment does not contain unnecessary electronics. It has both voice and remote control. It is also equipped with touch panels and color displays. Washing machines of this brand may seem old-fashioned to people who love modern gadgets. But at the same time, the absence of unnecessary electronics makes such equipment cheaper, and therefore more attractive to buyers.

It is also important for the user to learn how to properly start and configure an Indesit washing machine. In other words, to get a good result, you need to learn how to use the Indesit washing machine.

A few recommendations that every user will need:

• The laundry placed in the machine drum must be sorted. This should be done based on the type of fabric, color of the linen, color fastness, as well as the presence of weakly fixed elements on the linen.
• Before washing new items, you should check their labels. The manufacturer usually indicates on the label whether the item can be washed.
• It is important to check all pockets before placing clothes in the drum. Any small object that gets into an Indesit washing machine can cause serious problems. No less problems can arise if you accidentally wash an important document (passport, credit card, etc.). Therefore, it is better to immediately acquire this useful habit.
• Check that buttons are securely fastened to clothing before washing. It is also necessary to fasten zippers on clothes. And if clothes contain plastic zippers, then it is better to wash them in a specialized bag.
• It is advisable to turn clothes inside out before washing. Then it will wash off better.
• You should not wash many large items at once, this will worsen the balancing of the machine drum. It is better to mix small and large items and wash in several batches.
• Large items should not be washed one at a time. The result will be much higher if you put several small ones in the drum along with a large item.
• You should not use powders used for hand washing, because in this case too much foam is formed.
• Each detergent must be placed in the appropriate tray. Each product has its own powder receptacle compartment.
• If the laundry will be washed without heating the water, then you need to use half the amount of powder. After all, it will not dissolve completely in cold water and will be removed after washing with dirty water.
• The washing program can be selected only after stopping the Indesit washing equipment. Failure to do this may result in control module failure.

Original equipment in the company store

In addition to washing machines, Miele produces many types of reliable household appliances. Miele drying machines will help you dry your clothes to the “closet” state, refrigerators and freezers will help you keep food fresh, dishwashers will help you wash all the dishes quickly and efficiently, and ovens and hobs will help you create real culinary masterpieces.

All equipment located in the Miele company store is completely original and has all the necessary certificates of conformity. Household appliances are covered by a 24 month warranty. The user can order delivery to any region of Russia using transport companies. If you have any questions about Miele household appliances, ask them by phone or with the help of an online consultant. You can also visit one of the many Miele showrooms in Moscow and see for yourself the quality of premium equipment from Germany.